SolarEdge Inverters
SunCommon has installed several SolarEdge inverter models. From left to right they are the SetApp HD wave (screenless), HD wave (with screen), and SolarEdge A-US (with screen).
All SolarEdge inverters have a red ON/OFF toggle switch and a black DC disconnect dial.
How to power cycle (reset) your SolarEdge inverter
If you have a SolarEdge HD Wave or A-US Inverter displaying error codes or a SetApp inverter displaying a red fault light, then power cycling is a good next step. There are some error codes (Ground Faults and Isolation Errors) where it does not make sense for safety reasons. In those cases, contact SunCommon Customer Support.
How to power cycle a SolarEdge inverter:
1) Flip the red switch into the off “0” position. This is located either above the black dial/DC disconnect or on the left side in the back of your inverter.
2) If your inverter has a screen, wait until the DC voltage reading goes below 50 VDC. If your inverter does not have a screen, wait for 5 minutes.
3) Turn off the DC disconnect. This is the black dial right on the front of the inverter. Simply turn it to the “off” position.
4) Turn off your system’s AC disconnect. This is located outside next to your utility meter. Look for a grey box labeled AC Disconnect with a lever that you’ll pull down into the “off” position. If you do not see a grey box labeled AC Disconnect, look for a breaker underneath your Net Meter (ConnectDER). You will need to turn the breaker off. To do this, unscrew the grey cover to access the breaker. See reference photos.
5) Wait 30 seconds and then turn everything back on in reverse order. Throw the AC lever or breaker back to the “on” position, turn the dial on the inverter back to the “on” position, and flip the red switch back to the “1” position.
The inverter will start to turn back on and may take a few minutes to reboot. You should see the main screen as normal or the red fault light clear once the reboot is complete with no error message. If your inverter has a screen, please take a photo of any error messages that display while the inverter is rebooting and send them to [email protected]. If the issue is not resolved, please email [email protected] to create a case.
How to read your SolarEdge inverter screen
Your SolarEdge HDWave or A-US has several different screens and will cycle through these on a timer. The first screen is the most important:
Vac : The AC output voltage
Vdc : The DC input voltage
Pac : The AC output power – this is the amount of electricity your system is currently producing in watts
P_OK: XXX/YYY: This signifies the number of optimizers in the array and shows if any of those optimizers are not working. If XXX and YYY are not equal, there may be a problem in one or more power optimizers.
S_OK: Means that the connection to the SolarEdge monitoring portal is successful (appears only if your system is equipped with monitoring equipment and the inverter is connected to the server).
ON/OFF: Indicates the position of the red inverter ON/OFF switch.
For more detail, see this PDF from the manufacturer: SolarEdge Inverter status screens
What the lights on your SolarEdge inverter mean
If the blue light is on: Your inverter is communicating with the monitoring platformIf the green light is on: Your system is producing.If the green light is flashing: Your system is connected to the grid but is not producing. This can happen if there is snow covering the system or at night.
If the red light is on: There is a system error. The first step is to power cycle your inverter. If this does not resolve the issue, please email the Customer Support Team at [email protected] for further assistance.
View the SolarEdge LED guide for a full list of LED patterns and error codes
Common error messages seen on SolarEdge inverters and how to fix them.
Night Mode or Idle
Inverter goes into night mode or into idle when there is no light detected. Usually this is due to night time, snow cover, and large obstructions.
If your inverter is in Night Mode or Idle during the day when the system is free of snow, please try power cycling and then calling SunCommon Customer Support if the issue persists.
Don’t see your error code listed?
For a complete list of inverter error codes and their meanings, please click here.
18xC, 150
Arc Fault. This is an easy error to reset! Simply toggle red switch “off” wait 30sec then flip to “on” again.
2×19, 18×58
Ground Fault / Isolation Fault: Please contact SunCommon Customer Support
AC Over Voltage
Please contact SunCommon Customer Support
18xB7, 18xBC, 18xB5 “HW”
Hardware error a replacement inverter may be needed. Please contact SunCommon Customer Support
Back to Customer Support